Project 50 shades of grey - Canadian Amateur Modding competition 2018

[Tpbmods]

Taking a step back into Sept-Dec 2018 This was my CAMC 2018 Entry on the dazmode forums.

 

Components:

Mobo - ROG Maximus Code z370

CPU - i7 8700k Delidded/LM/Rockitcool Copper IHS

GPU - EVGA 1080TI FTW3

Ram - Teamgroup T-Force Delta 2 RGB 4x4

PSU - Corsair AX1000w (total overkill I know)

 

Storage:

M.2 - ADATA XPG sx8200 gen3 x4 240gb

SSD - Samsung 850 evo 500gb

SSHD - Seagate Firecuda 2tb

HDD - Seagate Barracuda Compute 4tb

 

Watercooling:

CPU - Watercool Heatkiller pro4 full nickle

GPU - EKWB Acrylic FTW3 TI

Pump - EKWB Revo D5 PWM

Radiators - Rad 1 - XSPC 360x45 Rad 2 - EKWB PL 360

Reservoir - Thermaltake 170mm

Temp Sensor - Thermaltake

Hardline Fittings - Thermaltake 16mm

Softline Fittings - EKWB 5/8 compression

Angled Fittings - Dazmode Darkside/Bitspower/Nanoxia

Bulkheads - Thermaltake/Nanoxia

Drain Valve - Dazmode Darkside Pushvalve system

Misc fittings - Dazmode Darkside for a vast majority of them

Tubing - Primarily Dazmode Darkside, But some Thermaltake in the mix.

 

Cables - Which I make myself!

Sleeving - Mainframe Customs Telios and Dazmode Darkside

Wire - 18awg that I ordered from PC Mods Canada

Connectors - Mainframe Customs and Dazmode (depends on the connector)

Pins - Mainframe Customs

Combs - A mix of Nanoxia CoolForce up front, and Dazmode darkside in the rear.

 

In the final hours, I actually won a facebook giveaway and got myself some Delta 2 RGB, which I decided I would swap to in the last minutes

Had a bit if dye fallout, which isnt that big of a deal. I didnt throw in anymore lights as it took away from the overall look.

Heres some photos of the final submission.

 

 

[ENTERPRISE]

 

Taking a step back into Sept-Dec 2018 This was my CAMC 2018 Entry on the dazmode forums.

 

Components:

Mobo - ROG Maximus Code z370

CPU - i7 8700k Delidded/LM/Rockitcool Copper IHS

GPU - EVGA 1080TI FTW3

Ram - Teamgroup T-Force Delta 2 RGB 4x4

PSU - Corsair AX1000w (total overkill I know)

 

Storage:

M.2 - ADATA XPG sx8200 gen3 x4 240gb

SSD - Samsung 850 evo 500gb

SSHD - Seagate Firecuda 2tb

HDD - Seagate Barracuda Compute 4tb

 

Watercooling:

CPU - Watercool Heatkiller pro4 full nickle

GPU - EKWB Acrylic FTW3 TI

Pump - EKWB Revo D5 PWM

Radiators - Rad 1 - XSPC 360x45 Rad 2 - EKWB PL 360

Reservoir - Thermaltake 170mm

Temp Sensor - Thermaltake

Hardline Fittings - Thermaltake 16mm

Softline Fittings - EKWB 5/8 compression

Angled Fittings - Dazmode Darkside/Bitspower/Nanoxia

Bulkheads - Thermaltake/Nanoxia

Drain Valve - Dazmode Darkside Pushvalve system

Misc fittings - Dazmode Darkside for a vast majority of them

Tubing - Primarily Dazmode Darkside, But some Thermaltake in the mix.

 

Cables - Which I make myself!

Sleeving - Mainframe Customs Telios and Dazmode Darkside

Wire - 18awg that I ordered from PC Mods Canada

Connectors - Mainframe Customs and Dazmode (depends on the connector)

Pins - Mainframe Customs

Combs - A mix of Nanoxia CoolForce up front, and Dazmode darkside in the rear.

 

In the final hours, I actually won a facebook giveaway and got myself some Delta 2 RGB, which I decided I would swap to in the last minutes

Had a bit if dye fallout, which isnt that big of a deal. I didnt throw in anymore lights as it took away from the overall look.

Heres some photos of the final submission.

 

 

 

Oh nice ! Is the case fully custom I assume ? I love the fact that you carried on the mesh look by popping it around the reservoir as well, finishes it off nicely...that and the maple leaf at the case front of course

 

Oh and do not forget to enter: https://extremehw.net/forum/main-forum/promotions-contests/1532-ehw-inwin-insight-giveaway-inwin-805-gaming-chassis

Edited October 2, 2019 by ENTERPRISE

[Tpbmods]

 

 

 

Oh nice ! Is the case fully custom I assume ? I love the fact that you carried on the mesh look by popping it around the reservoir as well, finishes it off nicely...that and the maple leaf at the case front of course

 

Oh and do not forget to enter: https://extremehw.net/forum/main-forum/promotions-contests/1532-ehw-inwin-insight-giveaway-inwin-805-gaming-chassis

 

Thanks @ENTERPRISE, This was a phantek Evolv ATX that I blasted apart with a jigsaw The case is absolute dogsh17 for airflow, so that was priority 1. Second was too give it a very raw and unfinished industrial look!

I will definitely share the giveaway, as I already follow and like everything. HOWEVER, I dont feel it would be fair for me to enter the giveaway sponsored by a company who already sponsors me

[ENTERPRISE]

 

Thanks @ENTERPRISE, This was a phantek Evolv ATX that I blasted apart with a jigsaw The case is absolute dogsh17 for airflow, so that was priority 1. Second was too give it a very raw and unfinished industrial look!

I will definitely share the giveaway, as I already follow and like everything. HOWEVER, I dont feel it would be fair for me to enter the giveaway sponsored by a company who already sponsors me

 

You certainly did attack it ! But in the best of ways. I would never have guessed it was the phantek Evolv to be honest, not after the work you did on it. Have you any current/upcoming mods ?

 

Thanks for the share and understand you not entering, very fair of you

[Tpbmods]

Currently working on an inwin 905 with the help of inwin/TeamGroup.

After that, inwin 925 as soon as it's available

[ENTERPRISE]

Nice ! I will have to keep my eye out for those

[Tpbmods]

Nice ! I will have to keep my eye out for those

 

They're all in the modding sub-forum

[ENTERPRISE]

Super blind is my middle name today ! Time to go and check them out.