Avacado

I recently had a comment on the Alta G1M case review that was posted on 01/15/22. I happened upon it by chance and responded to it. I never received a notification that anything had been commented on. Is it possible to enable this somehow so that readers who commented do not get missed?

Crap that's right. My bad.

Yea, it wasn't stable. I could probably get a CPUz bench run in, but thats all. I think i'll be able to run this at 4GHz 24/7 which I am pleased with. I bought a second QX6850 that I plan on delidding and having some fun with.

Try this. Mods made: TDP increase to 300w max Power target 300w max Voltage cap set to 1281.3mV PCI-e Rails to 150w max PCI-e slot increased to 75w max Temp target changed from 79.53c to 85c Max temp lowered from 91c to 90c I would like to see the voltage and wattage your card will pull with the TDP/power target increased. I raised your default boost cap from 1266 to 1430.5 which is boost table entry #74. This means the card should boost to this ON IT's OWN if temps are below 90c and power is sufficient. When you flash this I want to know if you are able to hit 1430.5 on core without instability. We can modify your RAM outside of Mtweaker. vBIOS modding is 100% geared towards core and very limited on RAM OC. I could set a RAM target but if we set that wrong it will crash the card easily. 970mod.zip

Yea, please let me know how it works out. These Maxwell Quadro's don't like running that high. The K quadro's were better in that regard. I would recommend putting that core on a cheap WB. I own a few of these and they work well. Computer PC GPU Water Cooling Block Universal Waterblock Liquid Cooler #3 WWW.EBAY.COM 1Pcs CPU Waterblock. Waterway: 0.8MM parallel waterway. Interface: G1/4 international universal thread. Material: copper bottom, top cover POM high temperature material. Model: graphics card core water...

Alright, I'll look into it. P0 state is any state outside of the clock table. So for example if your last clock state was #75 at 1500MHz, if you added +50 to core in X1 or AB, it would put it outside of the clock table and into P0 territory. I have not been folding as of late so things could have changed, but as I recall MEM OC does not help your PPD as much as CORE OC. I used to put a negative MEM offset on cards I would fold with just to devote 10-20 more w to core.

Will look at it tomorrow. Tell me what your limits are. What is the max stable clock you have seen. What max watts and voltage have you seen?

There were so many entries under your power table that I could not 100% identify which was the PCI-e slot. I modified the TDP and power limits to 100000. There were 3 additional entries that were >66000 so I increased the maximum on those to 100000. The remaining entries that were <66000 I did not touch as they would unlikely be your PCI-e slot wattage. Some of the voltage entries were 1.6mv, I capped all values at 1.281mv. The highest table entry your card had was 1228.0MHz. I changed your Boost frequency from a max of 1162.5MHz to 1228.0MHz. This means that the card can and should hit 1228.0MHz assuming it is lower than the 95c temp cap already assigned (You can set to whatever you are comfortable with) is getting the full 100w and caps at 1.281mv. If you can't hit 1228 or start getting instability, you can set a negative offset in Precision X1 or MSI afterburner for core frequency. If these settings do not work it means one of two things. 1. The card can't be flashed or did not take the flash. 2. I did not successfully identify and modify the correct power table entry for your PCI-e wattage. We can revisit 1&2 if it does not work. Please look over the vBIOS before flashing and make sure you are comfortable with it. 1.281mv,100w draw from PCI-e slot and a max temp of 95c are not things that are likely to give the card longevity. M2000.zip

Starting to creep up the 10x multiplier. 9 and 11 give consistent errors. Vdroop is MASSIVE on this board. I have to set 1.575v for 1.5v idle. It drops even lower when benching.

7 Series cards purchased.

It really is THAT cold in the dungeon. Though I suppose it could be an error. I am guessing the loop temp would have to be that low as well and it's not I have it setup in the dungeon (Basement) the dungeons ambient temps were in the 20's when I took that screen shot. Both windows are open a tad to help keep temps low and Radon levels at bay. I have some Acool digital temp display/probes. I can hook them up later and find out the real deal.

Welcome to the forums.

Yea, Cornell could wail. I saw Black hole sun a Soundgarden tribute band about 3 years back here in Asheville at the Orange peel. They were very good. I was shocked.

Pretty significant jump. I don't know anything about DOCP either. I had Threadrippers for a very short time till they were all sold.

Ill take a look this weekend.

Setup is so clean. Looking forward to watching this OC journey!

LGA 775/QX6850 Saying hi.

Dual core refers to the tubes within the rad itself.

So the x5470 was a no go. I tried so hard to install the microcode. BSOD's immediately when I managed to get into windows and multiple MOBO error beeps. It just did not want to let me do anything with it. Settled on the QX6850. I have never seen - temps on water before!!!

After the 660Ti's and 670 (Currently benching). Starting my conquest of the 700 series. Will be buying 770 Classy, 780 Classy and 780Ti Kingpin.

Not bad for a weekend snowed in. It won't last, but for now EHW is NUMBA WAN!

Heres mine. Some guy from Greece took my numba wan spot tho.

It's all good. Just thought you should know. If you plan on running more than 1 rad, you will be severely limited in flow.

Did you buy the gimped 1/2 flow corsair D5 ? Where is @ciarlatanoto help here. (He loves ranting about Corsair rebranding)